The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product collection of the entire gearbox and gear-electric motor system. Cat4CAD facilitates you in selecting and configuring the products, gives you the opportunity to print out comprehensive technical data bedding, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sized sizes.
Multiple Input Options: Essential gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple helical bevel gear reducer output Options: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, mounting pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Electric motor: Multiple leads and windings for globally multi volt/Hz requirements in addition modular design to simply accept brakes, encoders or pressured cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals on heat treated, plunge ground shafts
Shaft mounting options include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, encounter and flanged configurations. Gearmotors can be found in three phase high efficiency designs through 50 HP and single phase to 5 HP. We offer a variety of input and output shaft choices. Additionally, you will find fixed and variable speed motors and selection of ratios obtainable in this product offering.
Features
Accommodates insight power from ΒΌ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Vital dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying demands of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological content material of our products allows for an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully used in a multitude of industrial and civil applications. These are B-Series units which offer excellent value for money and result torque/weight ratio, especially due to the fact they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with small motor, PB-fitted for electric motor coupling with flexible joint
Casing with foot FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or ground profile
Gearing with 3 decrease stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to make sure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right position helical bevel equipment motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and will be offered with single or dual extended output shafts.
Units are also available as shaft mounted or with output flanges and are available for mounting horizontally or vertically. The units can also be provided with a bolt on torque reaction bracket and all variants can be found possibly motorised or with an insight shaft assembly.
Adding to the new range of Ever-Power helical gear motors this product takes benefit of our a long time of accumulated design knowledge together with the utilization of high quality materials and components. The outcome is a series of velocity reducing geared motors offering high load holding capacities, increased efficiency, quiet running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double essential oil seals, on input 
and output shaft since required.
All products are dimensionally interchangeable with other major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be fitted with a backstop module and reducer Devices can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemicals, pharma, packaging, food processing, plastic-type and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Switch on to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy materials, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, fine appearance ,and strong capacity to be overloaded.
6: Precise division and wide selection for transmission ratio.
7: The effectiveness is up to because high because 96% with low energy intake, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose use, convenient and low-price maintenance.
9: New seal device, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.