Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 electric motor. Ideal applications where an easy to fit, high torque result is required. Great for student based projects which includes robots and buggies.
The unit has been designed to ensure that the output shaft could be ‘clicked’ in and out for modification. E.g. cutting down to size. The electric motor is snap installed into its cradle to engage the apparatus and worm.
Details
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + engine: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the engine is not turning. The high gear ratios of 216:1 or 336:1 get this to gearbox appropriate for small walking robots, lifting mechanisms, and various other applications where high torque is usually desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draw up to a few amps, making them ideal applicants for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, also at very low voltages. We advise that you use stall-detection sensors, or simply watch your robot, to make sure that it doesn’t stall for more than a few seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works with the wheels that are compatible with Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also fits on small threaded end of the shaft, though it is not particularly designed to work with this type of shaft (the hub’s set screw could damage the thread on the shaft).
Ever-Power equipment motors are economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical correct position worm geared motors set new criteria for reliability, effectiveness and economic climate with unparalleled features including hollow shafts in the smallest sizes. An inverter friendly style provides for easy integration at this point and a future proof answer. The Ever-Power gear motor offers total flexibility in mounting options includes shaft, base, face, and flange solutions. The electric motor terminal box can be mounted in substitute positions rotated in 90º steps around the motor frame offering for unparalleled integration possibilities.
Ever-Power gear motors comply with North American and International standards, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a true total alternative for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose evidence,and can be used outdoors or in wet and dusty conditions without the use of additional enclosures. Full rated output is available at the output shaft of the machine.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With integrated inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm gear motors are the answer for applications requiring a corner turn, optional dual result, or an inability for the engine to be back again driven. The DC right angle equipment motors are made for constant and intermittent duty operation. Our right angle gear reducers are designed with many mounting plate choices, making them ideal for a variety of DC motor based applications. You can expect 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Standard brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are designed to generate high torque in a small package size. Worm Equipment Motors are great for applications that want a personal- locking or breaking feature because the result shaft can’t rotate when there’s no power applied. Additionally, Worm Gearheads can transfer motion in 90 degrees. With various reduction ratios, precision cut gears, voltages and sizes, EP Products has a DC Worm Gear Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Capability to Handle Large Gear Decrease Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Protection Door Locks / Industrial Conveying Systems / Security Gates / Dental care Chairs / Ambulance Cots & Stretchers Quite a few DC Motors can be complimented with among our Worm Gearheads. EP Items will work with you to create and produce a Worm Gear Motor that may optimize the efficiency of your specific application.
Built to your specific requirements
Electric motor Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Cut / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Additional Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm engine uses a metal gear box for toughness and a high torque output. Due to the special mechanical framework of the worm drive the engine output shaft can be self locking and may not be rotated.
This part runs on the two wire connection and supports direction control in addition to PWM speed control. Rated voltage is 12v and can achieve 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear systems from EP DRIVESYSTEMS especially show their strength in applications where high equipment ratios are necessary. Our worm geared motors are for that reason optimally suited for use in intralogistics, packaging technology and the meals & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions enable simple and effective cleaning of the drive system.
Corrosion protection
The NSD tupH sealed surface conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users optimum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are many applications that want drive systems, and each of these has its own unique requirements. The EP series worm equipment motors could be quickly and efficiently adapted to fulfill your needs.
Worm gear devices impress with their high power density and small style. If required, we are able to also supply them with the impressive nsd tupH surface treatment.
As well as the basic EP housing, we offer an extensive type of bolt-on elements to customize the product including torque arms, shaft covers and output flanges. These could be quickly field installed, but we will also be happy to assemble the individual components for you.
Find out more about the modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm gear unit SMI
SMI worm gear devices feature a even, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface area conversion makes this product ideally suited for severe and demanding industries like meals processing and pharmaceuticals.
Versatile input designs such as for example NEMA, IEC or direct motor mounts in extra foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units possess on all sides different fixing possibilities and enable an easy assembling for the client.
Other drive configurationscan be designed by use of built-on worm motor accessories (e.g. torque arm and output flanges). The housings are created in light weight structure out of aluminium die cast. Engine attachment is realised in general by means of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, result shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/installation:uniblock, flange, torque arm
Buy Worm Drive Gearbox with Motor – incorporating the next features: 1 to 6V voltage rating, 17100 rpm simply no load speed, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm wide, 40mm high, a robust worm drive gearbox powered by an MM28 electric motor (included), most ideal for applications where an easy to fit, high torque result is necessary, nylon housing and gear, requires light essential oil or silicon grease lubrication, ideal for student based tasks including robots and buggies.
Most suitable for applications where a simple to match, high torque output is required
Ideal for student based tasks including robots and buggies
Reversible High torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Features:
The electric motor is Gear DC motor with micro-turbine worm, you can change the wiring-connection to change motor rotation.
Turbo worm geared motor with self-lock, that’s, regarding motor without electric, the output axis is definitely fixed, self-lock.
The reducer output shaft arranged vertically with the electric motor shaft, whole motor output shaft relatively-short than general gear electric motor, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the window, door, Mini winch. Ect.
In sumo robot or combat robot competition where high holding torque’s motor is essential to avoid your robot being pushed by your opponent robot. The worm gear is certainly a better option compared to the spur gear motor. Why is worm gear so unique? Check this wiki out: Worm Drive.
“Unlike with ordinary equipment trains, the path of transmission (insight shaft vs result shaft) is not reversible when using large reduction ratios, because of the higher friction involved between your worm and worm-wheel, when usually a single start (a single spiral) worm is used. This is often a advantage when it is desired to get rid of any likelihood of the output driving the input.”
In other phrases, it is hard to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Output shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g